Painting Wooden Objects and Refinishing Them
Painting and refinishing wooden furniture comes with the feel and advantage of new furniture.
Painting must be done with utmost care, cause on that will depend the look and feel to your furniture.
Step 1: Getting Started The first step is to ensure that the wooden object is not wet.
In case it is, it has to be dried up completely.
If required one can even use a heat gun, but from a distance to help you avoid hapless fires and burn marks.
Blisters, splinters, and any such accidents can be avoided by using working gloves, splinters and face marks.
Step 2: Sanding The initial job will require a rough paper, while the next part will need a smooth sand paper.
It should be done smoothly so as not to cause heat.
Step 3: Electric Sander Sanding has always been a very hard or frustrating job, with the sand paper getting clogged up by the paint in no time.
Try using an electric sander to help you ease the job.
Step 4: Polishing After you are done with the sanding and polishing, all dust must be removed immediately so you can sweep it all off and start painting.
Step 5: chemical stripper The right kind of stripper always helps in getting the job get easier.
The right kind of striper always varies with the purpose you are using it for.
Liquid chemicals will help you get in spray form, to clean coatings or a couple of layers.
Step 6: use an open type of container The container to store the paint must have a wide mouth, to help get the paint out easily.
Step 7: Paintbrush coats Make sure you coat your paintbrush with enough paint to get at least a medium-sized area with some paint.
One may also use a spray but 4 inches away.
Step 8: painting directions Paint the brush stripper with one direction, to cover the object using the liquid and the painted coat brush.
Paint the areas that have not been covered with paint already.
Step 9: get the paint to soften up About 30 minutes to 1 hour is the time required to get the paint to soften up.
Step 10: test if the paint worked Rub the blade over a paint scraper in a circular motion.
The chemical has worked correctly if the scraper cuts into the paint.
Step 11: Sand the object again with the electronic sandpaper or sand by hand.
Step 12: use a scraper where the paint is thick, with electric sandpaper.
Step 13: Chemical Methods Wear face masks and gloves to avoid the accidents with chemicals.
Long pants and shirts with short sleeves are an added advantage.
Step 14: Apply some of the chemical on the paint using cotton.
If poisoning occurs, you can use a scraper to wipe it off.
Painting must be done with utmost care, cause on that will depend the look and feel to your furniture.
Step 1: Getting Started The first step is to ensure that the wooden object is not wet.
In case it is, it has to be dried up completely.
If required one can even use a heat gun, but from a distance to help you avoid hapless fires and burn marks.
Blisters, splinters, and any such accidents can be avoided by using working gloves, splinters and face marks.
Step 2: Sanding The initial job will require a rough paper, while the next part will need a smooth sand paper.
It should be done smoothly so as not to cause heat.
Step 3: Electric Sander Sanding has always been a very hard or frustrating job, with the sand paper getting clogged up by the paint in no time.
Try using an electric sander to help you ease the job.
Step 4: Polishing After you are done with the sanding and polishing, all dust must be removed immediately so you can sweep it all off and start painting.
Step 5: chemical stripper The right kind of stripper always helps in getting the job get easier.
The right kind of striper always varies with the purpose you are using it for.
Liquid chemicals will help you get in spray form, to clean coatings or a couple of layers.
Step 6: use an open type of container The container to store the paint must have a wide mouth, to help get the paint out easily.
Step 7: Paintbrush coats Make sure you coat your paintbrush with enough paint to get at least a medium-sized area with some paint.
One may also use a spray but 4 inches away.
Step 8: painting directions Paint the brush stripper with one direction, to cover the object using the liquid and the painted coat brush.
Paint the areas that have not been covered with paint already.
Step 9: get the paint to soften up About 30 minutes to 1 hour is the time required to get the paint to soften up.
Step 10: test if the paint worked Rub the blade over a paint scraper in a circular motion.
The chemical has worked correctly if the scraper cuts into the paint.
Step 11: Sand the object again with the electronic sandpaper or sand by hand.
Step 12: use a scraper where the paint is thick, with electric sandpaper.
Step 13: Chemical Methods Wear face masks and gloves to avoid the accidents with chemicals.
Long pants and shirts with short sleeves are an added advantage.
Step 14: Apply some of the chemical on the paint using cotton.
If poisoning occurs, you can use a scraper to wipe it off.
Source...